The magicBox transforms your Oberheim into a realtime MIDI controlled Synthesizer.
All parameters are editable via MIDI cc messages.
Works with all generic MIDI controllers or with an iPAD.
12HP_ENV_Filter, 12HP_ENV_Loudness, 12HP_LFO, 12HP_MIXER. 12HP_VCF_Model-D, 12HP_VCF SEM, 12HP_VCO_ARP, 12HP_VCO_Model-D, 12HP_VCO_SEM, 12HP_VCO_Wavetable_5p, 12HP_VCO_Wavetable_OL, 24HP_TinyStep 8 Step Sequencer
mLab EuroRack Modules12HP_NOISE, 12HP_VCO_Wavetable_6p, 18HP_VCF_microModular, 20HP_microModular_ENV_DUAL, 20HP_microModular_VCO, 24HP_MCV_Control, 24HP_polyModular_Quad_VCO_DDS, 24HP_SCOPE Wave Monitor, 24HP_TinyStep_with_Wavetable_VCO, 28HP_PSU
mLab Full Size ModulesminiModular_CV6, miniModular_CV6_Patchbay, miniModular_Mixer, miniModular_Modifiers, miniModular_Oscillator Bank, miniModular_Slave_Oscillator Bank, miniModular_Output
miniModular Keyboard, miniModular 12U Portable Rack
EuroRack SystemsmicroModular Keyboard, microModular Rack, SEM, System-ZERO
EuroRack with ER2BUSObermoog, System-06, System-07, System-08, System-10
To ensure a permanent professional connection, all of our modules are equipped with 1/4 'TRS switch jacks.
With the new ER II BUS standard, our modules can be interconnected.
This way we can pre-patch our fully modular systems.
Um eine dauerhafte professionelle Verbindung zu gewährleisten, sind alle unsere Module mit 1/4 'TRS-Schalterbuchsen ausgestattet.
Mit dem neuen ER II BUS-Standard kö
nnen unsere Module miteinander verbunden werden.
Auf diese Weise kö
nnen wir vollstä
ndig modulare Systeme vorab patchen.
Hand made in Germany
Download the Owners Manual
Download the RealTime MIDI-Sync manual
Download the Control map manager for windows
CvSix Analog Processor Silver Face
Hardware:
6 x analog CV OUT
3 x analog GATE OUT
1 x analog S-Trigger OUT
1 x analog DIN-Sync
1 x MIDI IN / OUT
Functions:
Realtime MIDI to CV Interface
Step Sequencer with up to 100 Notes, Pauses, Transpose.
RealTime Arpeggiator Hold & Transpose, Octave, Up, Down, Up/ Down.
RealTime Phraser Hold & Transpose, Forward, Backward, Fwd / Bwd.
MIDI Controller Routing.
Each CV OUT can be controlled by any MIDI cc#, Velocity, AfterTouch, Pitch and/or NoteNumbers on any MIDI Channel.
MIDI Sync.The Step Sequencer, as well as the Arpeggio or Phrase starts, stops and runs synchronously with incoming MIDI Clock.
Sync Delay gives your arrangement the perfect groove.
Sync Rate can be set to 1/2, 1/3, 1/4, 1/6, 1/8, 1/12, 1/16, 1/24, 1/32
DIN-Sync OUT slaves through incoming MIDI Start, Stop, Clock messages.
Power via USB or external 9V DC 300mA Power Supply (+ Center)
Firmware can be updated via USB.
CvSix Analog Processor Black Face
CvSix Analog Processor Modular Unit for FORMANT SYNTHESIZER
CvSix in action movie
We also do modifications and repair
don't hesitate to contact us for service
1. Connect a Silicon Labs CP210x USB to UART Bridge to your windows PC.
2. Go to the windows device manager.
3. Find the Silicon Labs CP210x USB to UART Bridge under COM/LPT.
3. Right click and select Properties.
4. Then go to the Port Settings tab and click Restore Defaults.
5. Then click Advanced and set the COM port to the lowest available number.
Now you are ready to configure your APC220 with a windows tool e.g. "RF-ANET" | "RF-Magic" all those are the same.
You must start this program in Administrator mode! A right click on the program icon pops up a menu. Chose to start the program as Administrator.
While starting, the program, then the APC220 EN pin must toggle Low/High and the SET pin must go Low. Now you should see the APC220 settings on screen. If not, You must select the right COM port and then click the Read button. If still no success, double check all your setting.
Now you can configure your pair of 2xAPC220 as follows:
both APC220 must have the same RF frequency (431..478MHz)
both APC220 must have the same RF RFx rate (e.g. 9600)
both APC220 must have the same Series rate (e.g. 9600)
both APC220 must use the same COM port
both APC220 must have the same Net ID, but must have a different Node ID!
parity must be disabled.
You might also use another USB adapter with a proper pinout. But to initialize the APC220, the EN pin must toggle Low/High once, before starting the windows tool.
APC220 running:In running mode, don't connect the EN pin, neiter the SET pin!
The APC220 pinout and physical connection for running mode is as follows:
GND, VCC, EN, RX, TX, AUX, SET
The Arduino serial pins must be crossed on the way to the APC220.
Connect the Arduino RX pin with the ACP220 TX pin and vice versa.
If you're using an USB/serial adapter at the Arduino site e.g. to flash a Pro Mini board, don't forget to disconnect it and support your Pro Mini with an external power supply instead of the USB/serial adapter. Otherwise, the Arduino RX pin can not receive serial data from the ACP220.
r.meurer APC220-Test german
APC220 setting:1. Schliessen Sie eine Silicon Labs CP210x USB-zu-UART-Bridge an Ihrem PC an.
2. Gehen Sie zum Windows-Geraetemanager.
3. Finden Sie die Silicon Labs CP210x USB-zu-UART-Bridge unter COM / LPT.
3. Waehlen Sie mit der rechten Maustaste die Eigenschaften.
4. Gehen Sie dann auf die Registerkarte Anschlusseinstellungen und klicken Sie auf Standardeinstellungen wiederherstellen.
5. Anschliessend klicken Sie auf Erweitert und stellen den COM-Port auf die niedrigste verfuegbare Nummer ein.
Jetzt sind Sie bereit, Ihr APC220 mit einem Windows-Tool zu konfigurieren, z.B. " RF-ANET" | " RF-Magic" .
Sie muessen dieses Programm im Administrator-Modus starten!
Ein Rechtsklick auf das Programmsymbol oeffnet ein Popup Menu.
Waehlen Sie hier "
als Administrator starten"
.
Beim Start des Programms, muss der APC220 EN Pin Low/High toggeln und der SET Pin muss auf Low gehen. Jetzt sollten Sie die APC220 Einstellungen auf dem Bildschirm sehen. Wenn nicht, muessen Sie den richtigen COM-Port auswaehlen und dann auf die Schaltflache Read klicken. Falls Sie nun immer noch keinen Erfolg haben, ueberpruefen Sie alle Ihre Einstellung.
Jetzt koennen Sie Ihre Paar 2x APC220 wie folgt konfigurieren:
Beide APC220 gleiche RF-Frequenz (431..478MHz)
Beide APC220 gleiche RF RFx Rate (zB 9600)
Beide APC220 gleiche Serie Rate (zB 9600 )
Beide APC220 gleicher COM-Port
Beide APC220 gleiche Net-ID, aber unterschiedliche Node-ID
Die Paritaet muss deaktiviert sein.
Sie koennten auch einen anderen USB-Adapter mit entstprechendem Pinout verwenden. Aber bevor Sie das Windows-Tool starten, muss der EN Pin einmal Low/High toggeln.
APC220 running:Nach erfolgreicher Konfiguration:
Im laufenden Betrieb darf weder der EN-Pin, noch der SET-Pin am USB-Adapter angeschlossen sein, oder beide PINs muessen auf High gesetzt werden.
Das APC220 pinout und die physikalische Verbindung finden Sie hier:
GND, VCC, EN, RX, TX, AUX, SET
Die Arduino serial pins muessen auf dem Weg zum APC220 gekreuzt sein.
Verbinden Sie den Arduino RX Pin mit dem ACP220 TX-Pin und umgekehrt.
Wenn Sie Arduinoseitig einen USB / Serial-Adapter zur Programmierung verwenden, z.B. um eine Pro Mini Board zu flashen,
Vergessen Sie nicht diesen zu trennen und Ihr Pro Mini mit einem externen Netzteil zu versorgen, andernfalls kann der Arduino RX Pin keine seriellen Daten vom ACP220 empfangen.
Die Parameter werden mittels TTL/UART (RX/TX) und dem SET PIN gesetzt.
1ms nachdem der SET-PIN auf Low gesetzt wird arbeitet der APC220 mit Standardeinstellungen 9600, 8N1, no flow chart.
Nun kann eine Befehlszeile gesendet werden.
TX antworten nach 200ms mit einem Echo.
Der Benutzer kann nach ueberpruefung der Daten den SET-PIN wieder auf High setzen.
10ms spaeter hat der APC220 die neuen Parameter uebernommen.
APC220 wird mittels eines ACSII Befehlssatzes konfiguriert.
Es gibt 2 Befehlsgruppen (RD = Read und WR = Write)
Es muessen Grossbuchstaben verwendet werden.
Parameter werden durch Leerzeichen getrennt.
Eine Befehlszeile muss mit(CR-LF) abgeschlossen werden.
Das Terminal program putty bedient sendeseitig leider kein CR-LF.
Bei Hterm hat man die Wahl des Befehlsabschlusses (CR-LF) per Enter Taste.
Damit funktioniert es einwandfrei!
Vor jedem Befehl muss zunaechst der SET-PIN High/Low getoggelt werden.
Anschliessend kann eine Befehlszeile gesendet werden.
Der Befehl zum Lesen aller Parameter lautet RD und die Antwort darauf ist: PARA 435000 3 9 3 0
Moechte man diese Parameter im APC220 speichern, so lautet die Befehlszeile: WR 435000 3 9 3 0
Plan your modular synthesizer rack on ModularGrid
Eurorack & Modular Synthesizers | Sweetwater
Workshop: Einstieg in die Eurorack-Welt - Teil 1 - AMAZONA.de
Kaufempfehlung: Die besten Module für dein Basis-Eurorack - AMAZONA.de
Eurorack Modular (3HE) | Schneidersladen Berlin - Modulare Synthesizer
How to build a modular synth: The ultimate Eurorack buyer' s guide (factmag.com)
How to get started with Eurorack modular synthesis - YouTube
Eurorack + Modular Synths - Perfect Circuit
Eurorack System planen leicht gemacht :: Bonedo
VCV - The Eurorack Simulator (vcvrack.com)
A beginner' s guide to EURORACK | synthmode.com
Top 5 Crazy Eurorack Modules of 2020: The Best, Maddest Modular Machines! - gearnews.com
Modulare Synthesizer: der Eurorack-Leitfaden für Einsteiger*innen | LANDR Blog
DETROIT MODULAR : eurorack : synthesizers : electronic gear
Modular Synthesizers | Eurorack Modules | MU Format - Vintage King
Modular Synthesizer Images, Stock Photos & Vectors | Shutterstock
Eurorack for Beginners - Planning your Setup - Optoproductions
Eurorack Kits - Raw Voltage - Modular Store Vienna
Professional Eurorack Cases for Modular Synthesizers - MDLR CASE
Eurorack | Electronic Music Wiki | Fandom
Eurorack-Gehäuse (justmusic.de)
Eurorack DIY Kits – Thonk – DIY Synthesizer Kits & Components